Pro Comp Distributor Wiring Diagram: A Complete Guide

If you are looking for a high-quality ignition system for your vehicle, Pro Comp distributor can be a perfect solution. A distributor is an essential component of your engine’s ignition system that sends high-voltage current to each spark plug in the correct firing order. In this article, we will discuss the Pro Comp distributor wiring diagram and its installation process to help you achieve the best performance of your engine.

What is Pro Comp Distributor?

Pro Comp is a popular brand in the automotive industry known for producing high-performance ignition systems, including distributors, coils, spark plugs, and other components. Pro Comp distributor is designed to provide reliable and consistent ignition timing, which results in improved engine performance, increased horsepower, and fuel efficiency.

The Pro Comp distributor is available in various styles, including mechanical and electronic distributors, with different advance curves to suit different engine types and performance levels.

Types of Pro Comp Distributor

1. Mechanical Distributor:

A mechanical distributor is a traditional type of distributor that uses mechanical weights and springs to adjust the ignition timing according to engine speed and load. It is a reliable and straightforward design that is easy to maintain and troubleshoot.

2. Electronic Distributor:

An electronic distributor is a modern design that uses an electronic module to control the ignition timing. It is more precise and accurate than mechanical distributors and offers better performance and fuel efficiency.

Pro Comp Distributor Wiring Diagram

The Pro Comp distributor wiring diagram is a simple guide that shows how to connect the distributor’s different components to the engine’s ignition system. The wiring diagram varies depending on the type of distributor and the engine’s make and model. Here is a general wiring diagram for a Pro Comp distributor:

Distributor Component Wire Color Description
Positive (+) Terminal Red Connects to the ignition switch’s output (+12V)
Negative (-) Terminal Black Connects to the engine’s ground
Distributor Cap Connects to the spark plug wires in the correct firing order
Vacuum Advance Green Connects to the carburetor’s vacuum port (if equipped)

Installation Process

A Pro Comp distributor installation process varies depending on the engine’s make and model and the type of distributor. However, here are the general steps you need to follow:

Step 1: Preparation

Before you begin the installation process, you need to gather the necessary tools and equipment, including a Pro Comp distributor kit, a spark plug gap tool, a timing light, a wrench or socket set, and a spark plug wire removal tool. Also, make sure the engine is cool and the battery is disconnected to prevent any electrical shock or accidental startup.

Step 2: Remove the Old Distributor

If you are replacing an old distributor, you need to remove it first. To do that, you need to locate the distributor’s position and mark it with a paint marker or masking tape to help you align the new distributor correctly. Then, remove the distributor cap and rotor, disconnect the spark plug wires, and loosen the distributor’s hold-down bolt with a wrench or socket set.

Step 3: Install the New Distributor

Once you have removed the old distributor, you can install the new Pro Comp distributor. To do that, you need to align the distributor rotor with the engine’s timing mark and insert the distributor shaft into the engine’s oil pump drive. Then, tighten the hold-down bolt and install the distributor cap and rotor. Finally, connect the spark plug wires according to the correct firing order and connect the wiring harness.

Step 4: Set the Ignition Timing

After you have installed the new distributor, you need to set the ignition timing using a timing light. To do that, you need to start the engine and let it warm up to operating temperature. Then, connect the timing light to the number one spark plug wire and adjust the distributor’s advance until the timing mark on the crankshaft pulley aligns with the timing tab on the engine block. Once you have set the timing, tighten the distributor hold-down bolt and recheck the timing with the timing light.

FAQ

Q1: What is the spark plug gap for a Pro Comp distributor?

A1: The spark plug gap for a Pro Comp distributor depends on the engine’s make and model and the type of spark plugs you are using. Consult the spark plug manufacturer’s specifications or refer to the engine’s service manual for the correct spark plug gap.

Q2: Can I use a Pro Comp distributor with a high-performance engine?

A2: Yes, Pro Comp distributor is designed to provide reliable and consistent ignition timing for high-performance engines. However, you need to choose the right distributor that matches your engine’s requirements and performance level.

Q3: How often do I need to replace my Pro Comp distributor?

A3: A Pro Comp distributor is a high-quality ignition system that can last for many years if properly maintained and serviced. However, you need to inspect your distributor regularly for signs of wear or damage and replace any faulty components to ensure optimal performance.

Q4: Can I install a Pro Comp distributor myself?

A4: Yes, you can install a Pro Comp distributor yourself if you have the necessary tools and knowledge of your engine’s ignition system. However, if you are not familiar with the installation process or unsure about your skills, it is better to seek professional help to avoid any damage to your engine.

Q5: How do I troubleshoot a Pro Comp distributor?

A5: If you experience any ignition problems with your Pro Comp distributor, such as misfiring, rough idle, or poor performance, you need to troubleshoot the system to identify the root cause of the problem. Here are some common troubleshooting steps:

  • Check the spark plugs and wires for damage or wear
  • Inspect the distributor cap and rotor for corrosion or carbon buildup
  • Check the ignition coil and module for proper operation
  • Inspect the vacuum advance system for leaks or malfunctions

If you still cannot identify the problem, consult a professional mechanic or contact the Pro Comp customer service for further assistance.

Conclusion

The Pro Comp distributor is an excellent choice for those who want to improve their engine’s ignition system’s performance and reliability. By following the wiring diagram and installation process explained in this article, you can install your Pro Comp distributor correctly and set the ignition timing to achieve better engine performance and fuel efficiency. If you have any questions or need further assistance, do not hesitate to contact Pro Comp customer service.