iFlight SucceX-E F405 Wiring Diagram: A Comprehensive Guide

The iFlight SucceX-E F405 is a flight controller that offers a lot of features at an affordable price. It comes with an F4 processing unit, an OSD, and an integrated BEC. To make the most of its features, it is essential to understand its wiring diagram. In this article, we will take an in-depth look at the wiring diagram of iFlight SucceX-E F405, its components, and how to connect it to your drone.

Components of iFlight SucceX-E F405

The iFlight SucceX-E F405 has several components that need to be wired together properly to make it work correctly. Here are the primary components of the iFlight SucceX-E F405:

  1. Flight Controller
  2. Power Distribution Board
  3. Electronic Speed Controllers (ESCs)
  4. Receiver
  5. Camera
  6. VTX (Video Transmitter)
  7. GPS (optional)

Each of these components has to be connected to the flight controller at specific locations to complete the wiring of the iFlight SucceX-E F405.

Connecting the Components to iFlight SucceX-E F405

Connecting the components to the iFlight SucceX-E F405 requires careful consideration of the wiring diagram. Here’s how to connect each of the components to the flight controller:

Powering the Flight Controller

The iFlight SucceX-E F405 board has two pads labeled VBAT and +5V. You can power the board via the VBAT pad with a voltage range of between 2S to 6S (7.4V to 25.2V), or via the +5V pad with 5V voltage input.

Connecting the Electronic Speed Controllers (ESCs)

The iFlight SucceX-E F405 board has four motor output pads labeled M1, M2, M3, and M4. Connect the ESCs to the appropriate motor output pads, ensuring the correct orientation, and soldering the signal wire to the signal pin and the ground wire to the ground pin.

Connecting the Receiver

Connect the receiver to the iFlight SucceX-E F405 board via the SBUS, IBUS, or PPM pad. You’ll also need to solder the GND (ground) and +5V (power) wires to the appropriate pads.

Connecting the Camera

The iFlight SucceX-E F405 board has a Camera Control pad labeled CTR. You can connect the camera to this pad, ensuring the correct connection orientation.

Connecting the VTX (Video Transmitter)

The iFlight SucceX-E F405 board has a pad labeled VTX. You can connect the VTX to this pad, ensuring the correct orientation of the wire.

Connecting the GPS (optional)

If you want to use a GPS system, the iFlight SucceX-E F405 board has a dedicated pad labeled TX6/RX6. Connect the GPS to this pad, soldering the appropriate wires to the correct pins.

FAQ

Question Answer
What is the iFlight SucceX-E F405? The iFlight SucceX-E F405 is a flight controller that’s used to control drones in the air. It comes with several features, including an OSD, an F4 processing unit, and an integrated BEC.
What components are needed to connect to the iFlight SucceX-E F405? The main components are Flight Controller, Power Distribution Board, Electronic Speed Controllers, Receiver, Camera, and VTX.
What is the voltage range for powering the iFlight SucceX-E F405 board? You can power the board with a voltage range of between 2S to 6S (7.4V to 25.2V) via the VBAT pad or via the +5V pad with 5V voltage input.
How do you connect the ESCs to the iFlight SucceX-E F405 board? You can connect the ESCs to the appropriate motor output pads (M1, M2, M3, and M4) on the iFlight SucceX-E F405 board, ensuring the correct orientation and soldering the signal wire to the signal pin and the ground wire to the ground pin.
Does the iFlight SucceX-E F405 support GPS? Yes, the iFlight SucceX-E F405 supports GPS, and it has a dedicated pad labeled TX6/RX6 where you can connect your GPS system.

Understanding the wiring diagram of the iFlight SucceX-E F405 is essential to make the most of its features. Follow this guide to connect the essential components to the flight controller and ensure you have a smooth flying experience with your drone.