If you’re looking for a reliable electric brake controller for your trailer, then look no further than the Draw Tite Activator 2. This controller is designed to give you complete control over your trailer’s brakes, ensuring that you can stop quickly and safely.
However, installing the Draw Tite Activator 2 can be a bit tricky, especially if you’re not familiar with wiring. To help you out, we’ve created this comprehensive guide on how to wire the Draw Tite Activator 2.
What is the Draw Tite Activator 2?
The Draw Tite Activator 2 is an electric brake controller that is designed to control the brakes on your trailer. The controller is mounted inside your vehicle and is connected to the trailer’s braking system. When you apply the brakes in your vehicle, the controller sends a signal to the trailer’s braking system, activating the brakes on the trailer.
The Draw Tite Activator 2 is designed to work with trailers that have up to 4 axles. It features an easy-to-use interface and adjustable brake output, making it a popular choice among trailer owners.
What Tools Do You Need?
Before you start wiring the Draw Tite Activator 2, you’ll need a few tools. Here’s a list of everything you’ll need:
| Tool | Description |
|---|---|
| Wire Cutters | To cut wires to the appropriate length |
| Wire Strippers | To strip wires of their insulation |
| Screwdrivers | To tighten screws and bolts |
| Tape Measure | To measure the length of wires |
| Socket Set | To remove the vehicle’s battery cable |
Once you have all of these tools, you’re ready to start wiring the Draw Tite Activator 2.
Wiring the Draw Tite Activator 2
The first step in wiring the Draw Tite Activator 2 is to locate the vehicle’s brake light switch. The brake light switch is usually located under the dashboard, near the brake pedal. Once you’ve located the brake light switch, you’ll need to disconnect the negative terminal of the vehicle’s battery to prevent accidental electrical shock or damage.
Next, you’ll need to connect the red wire from the Draw Tite Activator 2 to the brake light switch. This is usually done by splicing the red wire into the vehicle’s brake light wire. You’ll need to use a wire stripper to strip the insulation off of the brake light wire, and then connect the red wire from the Draw Tite Activator 2 to the exposed wire using a wire nut.
After you’ve connected the red wire, you’ll need to connect the black wire from the Draw Tite Activator 2 to the negative terminal of the vehicle’s battery. This is usually done by removing the negative cable from the battery and then attaching the black wire to the negative post using a wrench.
The next step is to connect the blue wire from the Draw Tite Activator 2 to the trailer’s brake wire. This is usually done by splicing the blue wire into the trailer’s brake wire. You’ll need to strip the insulation off of the trailer’s brake wire and then connect the blue wire from the Draw Tite Activator 2 to the exposed wire using a wire nut.
Finally, you’ll need to connect the white wire from the Draw Tite Activator 2 to the ground wire on the trailer. This is usually done by splicing the white wire into the ground wire on the trailer. You’ll need to strip the insulation off of the ground wire and then connect the white wire from the Draw Tite Activator 2 to the exposed wire using a wire nut.
FAQs
1. Do I need to install a brake controller on my trailer?
If your trailer has electric brakes, then yes, you’ll need to install a brake controller. A brake controller is required by law in most states and is essential for safe towing.
2. How do I know if my trailer has electric brakes?
If your trailer has electric brakes, you’ll be able to see them on the axles. Electric brakes will have a wire that runs to each brake, as well as a wire that runs to the brake controller.
3. Can I install the Draw Tite Activator 2 myself?
Yes, you can install the Draw Tite Activator 2 yourself if you have the necessary tools and experience with wiring. However, if you’re not comfortable with wiring, it’s best to take your vehicle and trailer to a professional.
4. My Draw Tite Activator 2 isn’t working properly. What should I do?
If your Draw Tite Activator 2 isn’t working properly, the first thing you should do is check your wiring. Make sure all of the connections are secure and that there are no loose wires. If your wiring is correct, then you may need to replace your brake controller.
5. Can I use the Draw Tite Activator 2 with a trailer that has more than 4 axles?
No, the Draw Tite Activator 2 is only designed to work with trailers that have up to 4 axles. If you have a trailer with more than 4 axles, you’ll need to use a different brake controller.
Conclusion
Wiring the Draw Tite Activator 2 is a straightforward process, as long as you have the right tools and know-how. By following the steps outlined in this guide, you’ll be able to wire your brake controller quickly and easily. If you run into any problems, don’t hesitate to seek help from a professional.
