Jeep Commander owners who are planning on upgrading their car stereo system may want to know how to deal with the factory amp. Fortunately, there is a wiring diagram that can help them figure out how to bypass or integrate the amp. In this article, we will discuss the 2006 Jeep Commander factory amp wiring diagram in detail.
What is the Factory Amp?
The factory amp is a device that amplifies the audio signal from the head unit and sends it to the speakers. In the 2006 Jeep Commander, the factory amp is located under the rear seat. The amp has four channels, two for the front speakers and two for the rear speakers. The amp also has a subwoofer output.
Why Bypass or Integrate the Factory Amp?
Some car stereo enthusiasts prefer to bypass the factory amp and connect the head unit directly to the speakers. This is because factory amps are not always powerful enough to handle aftermarket speakers or subwoofers. By bypassing the amp, the signal is cleaner and stronger, resulting in better sound quality.
On the other hand, some Jeep Commander owners prefer to integrate the factory amp into their new stereo system. This is because the amp is designed to work with the car’s electrical system, and removing it may cause problems. By integrating the amp, the owner can use the factory wiring and speakers, while still enjoying the benefits of a new head unit.
Bypassing the Factory Amp
To bypass the factory amp, you will need to remove the rear seat and locate the amp. Once you have found the amp, disconnect the wiring harnesses from it. You will then need to connect the head unit directly to the speakers. This can be done using a wiring harness adapter, which can be purchased from a car audio store. The adapter will allow you to match the wires from the head unit to the wires on the speakers.
To bypass the subwoofer output, you will need to connect a line output converter (LOC) to the rear speaker wires. The LOC will convert the speaker-level signal to a preamp signal, which can be connected to an aftermarket amplifier. The aftermarket amplifier can then be connected to the subwoofer.
Integrating the Factory Amp
To integrate the factory amp, you will need to use a wiring harness adapter that is designed to work with the amp. The adapter will match the wires from the head unit to the wires on the amp. You will then need to connect the amp to the speakers using the factory wiring harness. This will ensure that the amp works properly with the car’s electrical system.
To integrate a subwoofer, you will need to connect an aftermarket amplifier to the subwoofer output on the factory amp. You can do this using a line output converter (LOC), which will convert the speaker-level signal to a preamp signal. The LOC can then be connected to the aftermarket amplifier.
2006 Jeep Commander Factory Amp Wiring Diagram
Here is a wiring diagram that shows how to bypass or integrate the factory amp in a 2006 Jeep Commander:
| Wire Color | Function |
|---|---|
| Gray/Light Green | Left Front Speaker (+) |
| Gray/Dark Green | Left Front Speaker (-) |
| Tan/Yellow | Right Front Speaker (+) |
| Tan/Dark Green | Right Front Speaker (-) |
| Dark Blue/Light Green | Left Rear Speaker (+) |
| Dark Blue/Yellow | Left Rear Speaker (-) |
| Dark Green/Light Green | Right Rear Speaker (+) |
| Dark Green/Yellow | Right Rear Speaker (-) |
| Yellow/Green | Subwoofer (+) |
| Gray/Orange | Subwoofer (-) |
FAQ
How Do I Know If I Need to Bypass or Integrate the Factory Amp?
If you are planning on upgrading your car stereo system with aftermarket speakers or subwoofers, you may need to bypass the factory amp. However, if you want to keep the factory speakers and wiring, you may want to integrate the factory amp.
Can I Bypass the Factory Amp Without Removing It?
No, you will need to remove the factory amp to bypass it. The amp is located under the rear seat, and you will need to remove the seat to access it.
What Is a Line Output Converter (LOC)?
A line output converter (LOC) is a device that converts a speaker-level signal to a preamp signal. This allows you to connect an aftermarket amplifier to a factory radio or factory amp.
Do I Need to Connect the Subwoofer to the Factory Amp?
No, you can connect the subwoofer to an aftermarket amplifier instead. However, if you want to use the factory subwoofer, you will need to connect it to the factory amp.
Can I Upgrade the Factory Amp?
Yes, you can upgrade the factory amp if you want to. However, be sure to choose an amp that is compatible with your car’s electrical system and speakers.
