If you’re looking for a 1995 Subaru Legacy stereo wiring diagram, you’re in luck. In this article, we will provide you with all of the information you need to install a new stereo in your Legacy. We’ll go over the wiring diagram, explain how to remove the old stereo, and give you tips for a successful installation. Let’s get started!
Wiring Diagram
The wiring diagram for a 1995 Subaru Legacy stereo is relatively simple to understand. There are three main components to the wiring: the power source, the speakers, and the antenna. Here’s a breakdown of each component:
| Wire Color | Function |
|---|---|
| Yellow | 12V Constant |
| Red | Ignition Switched 12V |
| Black | Ground |
| White | Front Left Speaker Positive |
| White/Black Stripe | Front Left Speaker Negative |
| Gray | Front Right Speaker Positive |
| Gray/Black Stripe | Front Right Speaker Negative |
| Green | Rear Left Speaker Positive |
| Green/Black Stripe | Rear Left Speaker Negative |
| Purple | Rear Right Speaker Positive |
| Purple/Black Stripe | Rear Right Speaker Negative |
| Blue | Antenna |
As you can see, the wiring diagram is fairly straightforward. The yellow wire should be connected to a constant power source, such as the battery, so that the stereo will retain its memory settings even when the ignition is turned off. The red wire should be connected to an ignition-switched power source, such as the accessory fuse, so that the stereo will turn on and off with the car. The black wire should be grounded to the car’s chassis.
The white, gray, green, and purple wires are the speaker wires. Each wire should be connected to its corresponding speaker’s positive and negative terminals. Finally, the blue wire is the antenna wire and should be connected to the car’s antenna.
Removing the Old Stereo
Before you can install a new stereo in your 1995 Subaru Legacy, you’ll need to remove the old stereo. Here’s how to do it:
- Disconnect the negative battery cable to avoid any electrical issues.
- Remove the trim panel surrounding the stereo by gently pulling it away from the dash. This may require a special trim removal tool.
- Unscrew any screws or bolts holding the stereo in place.
- Pull the stereo out of the dash until you can access the wiring harness and antenna cable.
- Disconnect the wiring harness and antenna cable from the back of the stereo.
- Remove the stereo from the car.
Installing the New Stereo
Now that you’ve removed the old stereo, it’s time to install the new one. Here’s how:
- Connect the wiring harness and antenna cable to the back of the new stereo.
- Slide the stereo into the dash until it clicks into place.
- Screw in any screws or bolts that held the old stereo in place.
- Replace the trim panel surrounding the stereo.
- Reconnect the negative battery cable.
- Turn on the ignition to test the new stereo.
FAQ
Can I install a new stereo myself?
Yes, you can install a new stereo yourself as long as you have the right tools and follow the instructions carefully.
Do I need a wiring harness adapter?
Yes, you will need a wiring harness adapter to connect the new stereo to the car’s wiring. This will ensure that the wiring is correct and that the stereo works properly.
What size stereo fits in a 1995 Subaru Legacy?
The stereo size for a 1995 Subaru Legacy is a single DIN.
Can I replace my old stereo with a touchscreen stereo?
Yes, you can replace your old stereo with a touchscreen stereo as long as it fits the single DIN size and you have the appropriate wiring harness adapter.
How do I remove the trim panel surrounding the stereo?
You can remove the trim panel by gently pulling it away from the dash. This may require a special trim removal tool.
Can I use the existing speaker wires to connect my new stereo?
Yes, you can use the existing speaker wires to connect your new stereo as long as you connect each wire to its corresponding speaker’s positive and negative terminals.
With this information, you should have everything you need to install a new stereo in your 1995 Subaru Legacy. Good luck!
